Secure Global Desktop Administration Guide
> Arrays, servers and load balancing
> Tuning application server load balancingSecure Global Desktop Administration Guide
> Arrays, servers and load balancing
> Tuning application server load balancing
Administrators can tune application server load balancing by editing application server load balancing properties. These properties affect:
This topic describes how you can tune load balancing and assumes you understand how Secure Global Desktop load balancing works.
The weighting property allows you to factor the relative power of the application
servers in to the decision Secure Global Desktop takes as to where to launch an application. This is discussed in Configuring load balancing.
The primary Secure Global Desktop server in the array contacts the load
balancing service on an application server on port 3579/tcp.
This is controlled by the listeningport property.
The load balancing service sends updates to the primary Secure Global Desktop server
on port 3579/udp. This is controlled by the probe.listeningport
property.
These ports are registered ports and you should only change these properties if Secure Global Desktop Support asks you to. You will need to open these ports if you have a firewall between the primary Secure Global Desktop server and the application servers.
The connectretries property is the number of times the
primary Secure Global Desktop server tries to connect to an application server to
request load updates.
The interval between each attempt is controlled by the shorttimeout property.
If the attempts to connect fail, the Secure Global Desktop server waits for the period of time
controlled by the longtimeout property before trying again.
For example, using the defaults for these properties, the Secure Global Desktop server makes 5 attempts
(connectretries) to contact the application server at 20 second intervals (shorttimeout).
If all 5 fail, Secure Global Desktop waits 600 seconds (longtimeout) before making 5 more
attempts at 20 second intervals.
You might want to change the timeout properties, for example, if your application server takes a long time to reboot.
The scaninterval property controls the period of time
between scans of the Secure Global Desktop server's list of load-balanced application servers.
The scan checks for the application servers that need to be contacted to
request a load update (connectretries).
The sockettimeout property controls how long it is before
a Secure Global Desktop server gets an error by trying to contact the load balancing
service when there is no data available.
The probe.samplerate and probe.windowsize properties
control how often the load balancing service measures the application server's
average load.
For example, the probe.samplerate is 10 seconds and the
probe.windowsize is 5. After 50 seconds (5 x 10), the 5 measurements
needed to calculate the average have been taken. After a further 10 seconds,
the load balancing service takes a new measurement, discards the oldest measurement
and then calculates a new average load.
You can increase/decrease the frequency of the calculation depending on how often you expect the application server load to change. For example, do users start applications at the start of the day and then close them at the end, or do they repeatedly start and stop applications.
The replyfrequency property controls the interval at which
the load balancing service send updates to the primary Secure Global Desktop server.
The percentagechange property controls the minimum
percentage change in CPU/memory use that must be reported
to the primary Secure Global Desktop server. The load balancing service sends
these updates as soon as the percentage change occurs. For example if an
application server is running at 30% CPU load and the
percentchange value is 10, an update occurs
when the load is either 20% or 40%. The load balancing service takes into account sudden
'spikes' of activity and also makes adjustments when, for example a server reaches
81% CPU load and the percentagechange value is 20%.
The replyfrequency updates are sent even if the load does not change
and even if there has been a percentagechange update.
The basis for the percentagechange calculation is reset every time
there is a replyfrequency update.
If there is no update from an application server for
updatelimit x replyfrequency seconds,
Secure Global Desktop considers the application server to be 'out of contact'.
This means the application server is marked as unavailable to launch
applications until the Secure Global Desktop server can re-establish contact with it.
Secure Global Desktop considers the CPU/memory data to be
too unreliable if there has been no update from the application server for
maxmissedsamples x replyfrequency seconds.
Note The load balancing service sends updates even if the load does not change.
If the data is unreliable, the data is ignored when making the decision on where to launch an application. The net effect of this is to make the application server the last in the queue so that it will only be used to launch applications if no other server is available or suitable.
The primary Secure Global Desktop server sends CPU/memory load updates to the other
members of the array every
maxmissedsamples x replyfrequency/2 seconds. This update takes
place even if the load does not change.
If a secondary Secure Global Desktop server misses an update, it considers the load data it has to be unreliable and reverts to the Fewest application sessions method of load balancing. It uses this method until it receives a new update.
Copyright © 1997-2006 Sun Microsystems, Inc. All rights reserved.